If carbon is deposited, remove it using a spark plug cleaner machine or carefully use a tool with a pointed end. If any damages are found, replace the brake disc cover with a new one. O-ring : Do not reuse. Then, those of us who don't mind paying for a product that is worth it's cost pay for everyone else's freeloading. B933H24306004 8 Apply a small quantity of thread lock to the brake Removal caliper mounting bolts 4. B933H24306004 8 Apply a small quantity of thread lock to the brake Removal caliper mounting bolts 4. If push rod does not slide smoothly, replace the cam chain ten- sion adjuster with a new one.
If any defects are found, replace the shock absorber with a new one. Damage or worn rear axel housing bearings. Do not reuse the removed dust seals. If nobody wants to pay for them, they won't get printed anymore. Insufficient amount of engine oil.
Inspect the camshaft journal wear in the following Service limit: 0. Starting from the roller pin that is faces and camshaft journal holders. Mode select switch coupler 16. For this purpose, use of an inspection form such as below will facilitate collecting information required for proper analysis and diagnosis. Intake Exhaust 45° N-128 N-128 15° — N-121 30° N-128 — 60°. The removed stopper ring must be replaced with a new one.
Do not use compressed air on the carburetor body before removing the diaphragm;. The locknuts 2 with a yellow finished surface have left-hand threads. Worn or distorted gearshift fork. If the resistance is not within the specified value, replace the starter relay with a new one. The engine starts fine when it is cold. Gear position switch 1 Remove the gear position switch 1. Special tool B : 09920—53740 Clutch sleeve hub holder 13 Remove the clutch sleeve hub nut.
Starter motor : Bind the brake switch with the clamp. Any help or advice would greatly be appreciated. Master cylinder clamp bolt: 10 N·m 1. Battery has been left in a run-down condition for a long Replace. Starter valve : Do not reuse. Buy Now and receive immediate access to this manual! Pay attention to the following points.
With this Step by Step Manual You can easily disassembly and assembly overhaul even engine. The thickness of the is out of specification, replace the valve with a new one. Clamp Ignition coil Battery terminal Starter relay coupler Pass the starter motor lead wire Clamp and starter relay lead wire Generator. After disconnecting the throttle cable, do not snap the throttle valve from full open to full Throttle Body Removal and Installation close. Immediately wipe off any brake fluid contacting any part of the vehicle. Inspect the steering shaft bushing for wear or damage. Starter torque limiter 1 Remove the starter torque limiter cover 1.
Starter valve : Do not reuse. I933H1440009-01 I933H1440012-03 5 Set the parking brake shaft 6 in neutral position by 10 Adjust the parking brake. Keep heat, sparks and flames away from gasoline. B933H21906008 2 Remove the generator cover 1. B933H29306010 If any abnormality is found, replace the ignition Inspect the ignition switch in the following procedures: switch with a new one.
Repair manuals allow those of us who are capable to do things ourselves, without relying on a mechanic. I649G1520056-03 Gearshift fork groove width Measure the gearshift fork groove width using the. Maintenance intervals are expressed in terms of kilometers, miles and months, and are dependent on whichever comes first. Refer to Inspect the oil seal lips for wear or damage. Removal 1 Remove the throttle lever case 1.
Disassembly 1 Remove the water pump cover 1. The tube- and-fin type radiator is made of aluminum, which is characterized by lightness in weight and good heat dissi- pation. I say just suck it up, pay the money and buy the darn book. B933H21A06004 Removal 1 Drain engine oil. The removed snap ring 14 must be replaced : Thread lock cement 99000—32110 with a new one. O-ring : Do not reuse.
Do not reused the removed O-ring in order to prevent leakage of oil. Tightening torque Main oil gallery plug a : 18 N·m 1. It was crammed jam-packed full of dust, rust, and mud. Do not use compressed air on the carburetor body before removing the diaphragm;. Loose rear wheel hub nuts.